PSEQT 10" 15 LED Trailer Brake Tail Light Bar Stop Change Tail Lights Assembly ID Clearance Strip Red Light Waterproof for Wrangler Golf Cart Offroad Truck RV UTV ATV

came quick. looks good . packaged well.

PSEQT 10" 15 LED Trailer Brake Tail Light Bar Stop Change Tail Lights Assembly.I have been running these lights on my 2023 RAM as added turn/stop lights. I have learned to test the connections prior to soldering, clamping or doing anything for a permanent connection on any light. I tossed the instructions and tested.I also learned to seal any of these add on trailer type lights (LEDs). I used a clear RV window sealant that remains pliable to some degree. I filled the joint between the red lens and the black body (filled it in) and dabbed a bit on where the wires enter the black body of the lights. I purchased these about mid 2023 and it is now 30 November of 2024. No leaks and all the lights are working.I mounted them below my tailgate using the double sided tape provided and then added some small stainless steel bolts, nuts and washers to really secure them. The black plugs fit in just fine to cover the shiny bolt heads. Yes these are very small bolts.I then soldered additional wire to the light leads. I ran all the wires through a plastic loom behind the bumper and soldered on a 4-prong trailer plug. I simply insert the plug into the RAM trailer towing receptacle provided by the manufacturer. When towing a trailer I don’t want these working along with the trailer lights, they probably would not be seen.I have not had any problems with my lights or instillation. An inexpensive way to add a little safety to your vehicle.

Nice and bright lights

Used these to add some additional signal, running and break lights on our travel trailer. Factory lights are too low for visibility. Install was easy enough. Lack of instructions that include wire identification is a disappointment, this indicates to me the company that makes and sells these does not care about user experience.Now why they get a 4 star and really deserve a 3 star. The visible angle of the LEDs is vary narrow, meaning when a car is in the passing lane or off to the side the will likely not see these flash. Additionally they are not very bright compared to other signal, running, and break lights.If these go out I would not replace with the same brand.

DO NOT BUY, if you want to use them as turn signals! These lights Must have constant voltage for the sequential function to work. If you just try to splice them into your cars, turn signal wiring harness the lights will barely flicker. The natural pulse your vehicle turn signal creates does not allow the sequential operation of these lights to work!

Muy Bueno productos los proveedores tambien necesito facturas para las compras nunca mandan facturas siempre deben mandar siempre facturas para las compras y los clientes

The media could not be loaded. Installed the smoked lens version on my rear bumper and the amber lens version on the inside of the rear glass. Both are plenty bright during the day and at night.Don't give these a bad review for simply not having instructions; It's simple!BLACK wire is GROUNDRED wire is "low brightness/constant on"YELLOW wire is "high brightness/sequential turn signal"Great lights so far. Installed them on 9/15/2023. Only time will tell.

UPDATE: I redid all of the grounds and I know they are good. All bare metal connections and the trailer lights work perfectly. My issue is still with these new LED lights.I have left and right directional. I have break lights, I even have break lights when I use the directional.What I do not have is the lights working with my head lights. When I put on the head lights I do not get these to light up. When I put on a directional I still get all of the side markers (both sides of the trailer) flashing along with these new lights and ny trailer directionals.I went as far as to swap out the wires and connect the black where I had the red and the red to the black and I even connected them all together! The results were not good though one combination did get me the driving light on but nothing else. I am settling for the original configuration and I will sacrifice no driving light and have flashing side markers . No idea what else I can try. I mean it is a simple flat standard trailer connection (white, brown, yellow, green) and all other lights I have ever bought (this trailer, boat trailers) worked as designed.I connected these to my existing wiring on my utility trailer. I put the black wire to the brown (tail light, side market, license plate light), the Red wire the Yellow and the Green (LH stop and turn signal and RH stop and turn signal). Whit was connected to ground. My issue is when I turn on a directional all of the side markers also flash. DOesn't matter if I do Left turn or Right. If I disconnect the brown wire I lose the directional function of these lights. I also tested the ground and that is working well.***************************************************Anyone know how to wire these so the side markers do not flash with the directional lights? I am confusing people (I think) if all four side markers flash when I am taking a left turn (or a right turn).