Hobart 194776 Small Running Gear/Cylinder Rack, Black

Well made cart but do NOT use the sheet metal screws (cheap metal, poor sizing). I drilled mine and used 1/8" bolts & screws to assemble - worked great and will last forever.

Great cart for the price. Works wells holding the a Hobart 140.

This cart fits the Hobart and similar welders. The gas cylinder pylon has chain slots that work together very well to make replacing the gas cylinder a quick convenient job, a welcome change from the time consuming nylon cargo strap type found on several similar products. The cart's generous lower tray has deep enough edges to restrain the wire spools, nozzles, contact tips anti-splatter , MIG pliers and several vise-lock welding clamps that are essential accessories for any MIG welder. The only shortcoming of this cart appeared after more than a few uses, the small front casters aren't really capable of carrying the weight and the ball bearing swivel post gradually loosens until it suddenly disintegrates. Its not the most common wheel post diameter and post length combination, but there are more competent swivel casters on Amazon to replace them with. Choose a replacement withas much weight bearing capability as may be available. If I had it to do again, I would replace the casters when I first assembled the cart. Hindsight is 20/20 ... Its still the right cart, another $12-15 for better casters is well worth it.

Nice stand, enables good use of space, ease of moving the welder around projects. A few screws were undersized & cheap. Replaced with correct hardware out of my stock. Mr Hobart this is stand has your name on it. Reflects your interest in quality. If I found this quality level on my new Hobart welder it would be returned.

The hardware on this thing is trash. I just drilled my own holes and used my own screws. Once you do that this rack is pretty awesome and is really sturdy. I have an 80cu bottle and a hobart 210 on mine and am not worried about this thing at all. But, it is really disappointing that Hobart ships this with the cheapest of cheap Chinese hardware that strips out halfway through putting it on. I would give this thing five stars but I literally had to drill holes for all the screws and I expected a lot more from Hobart.

I purchased this cart for my Hobart Handler 140 after seeing it on this site for almost half off. The reviews I read were concerning, but I bought it anyway since most of the complaints were the sheet metal screws it came with. I had no problems during assembly and my welder fits on it perfectly. This is a very nice cart.

What a horrific product! I read some of the negative reviews here, but I figured the product couldn't possibly be that bad. Turns out it's actually worse! NONE of the holes lined up, I ended up having to re-drill half the holes to get the bolts to go in. The "bolts" are a joke in themselves. They're just cheap sheet metal screws. You screw them into... sheet metal! There are NO threads anywhere on this entire cart! And since the sheet metal is so thin, stripping out the holes happens on a whim. The axle shaft for the rear wheels wasn't long enough, I couldn't get the cotter pins to go in unless I removed all the washers first. At least I was able to use the bushings... Also worth noting, there's nowhere to hang anything. No hooks, no handles, nothing at all. Just moving it around is a challenge. This is about as barebones as it gets. I wanted something short to reduce the likelihood of the cart tipping over, but without any means of pushing/pulling it around, the reduced height ends up being a negative. What's really sad is how this cart contrasts with the Hobart welder I bought it for. The Hobart Handler 140 is top notch quality in every respect. But this cart is an embarrassment by comparison. A terrible companion to the excellent welder. If I were Hobart, I'd be ashamed to have my name on this horrible product. There's absolutely nothing here to justify the price. I *might* have found this acceptable at $40... maybe. I had an a cart a couple years ago that I bought for $80, and it put this one to shame. Selling it was a huge mistake.

I compared carts and I kept coming back to this one because I like the low-profile design. I also like the fact that the top shelf is not angled. The cart went together well, no issues - after reading some of the reviews I wasn’t sure what to expect, but this is a good cart and it fits my Hobart Handler 140 MIG welder very nicely.

Buen tamaño muy practico movible no ocupa mucho espacio, si le colocaran un tubo para guiar sería excelente

This thing is junk. Light duty held together with sheet metal screws. You probably own a welder. Just make one.

EN GENERAL ME GUSTO EL PRODUCTO SIN EMBARGO NOTE QUE LOS TORNILLOS QUE TRAE PARA APRETAR LAS CHAROLAS SE BARREN Y NO APRIETAN BIEN COMO DEBERÍA.

Excelente yo lo adquirí a una 3ra parte de su precio lo arme fácil y quedó muy robusto lo recomiendo. La Soldadora también la compré por Amazon y Funciona muy bien.