uxcellFoam Tubing for Handle Grip Support, Pipe Insulation, 25mm(1") ID 35mm OD 1m Length Black

I used this on the bench press section of my weight machine. I used a little water to slip it on to the handles and it installed really easy. The rubber seems sturdy, and it looks like it will last a while.

Great for replacing a worn out cork grip.

Had to use water and air hose from my air compressor to slip this pad on. Tight fit.If you ever used compressed air to remove mountain bike handle bar grips this same method worked to get this pad on. Just blow air under one end and pull down. The air cushion helps to stretch the pad. Once close to the end go to top to blow air and push down. Takes a little finesse but after 5 minutes the pad was on.

I bought this to replace the foam tubing on the handle of my spa cover lifter. The original foam tubing had rotted and was falling out. Lift manufacture did not sell replacement and had no suggestions for a replacement, so I went looking for something and found this product. The 1 meter length is long enough for me to make two sets of replacements. Product was easy to cut and install. So far holding up extremely well so I could not be happier. If you are using a long piece more than 6" installation is made easier if you get the inside of the tubing wet. I just put it under the faucet and let water run through the center. With the tubing wet, it will slide over the bar or handle much easier. After the tubing dries, it will stick to the bar and not move. This of course assumes you by the tubing with an inner diameter equivalent to the bar or handle that you are installing it on.I showed this to the spa dealer I bought my tub from, and they immediately bought this product to sell to their customers. They were impressed with quality and how well it worked.

I am so pleased to have bought this type of grip handle, it is so soft, firm and strong 💪 for my project I used it on! Thanks I highly recommend buying this product 👌 👍!💯😀

This tubing insulation is just what I needed to give new life to my tripod. The foam pipe insulation I had around it before was starting to disintegrate and was looking shabby. This foam tubing isn't like the foam insulation for water pipes. It's more like neoprene material, except without the outer fabric layer. It really does insulate (more on that later) and provides a nice grippy surface to hold onto. The only problem is the way it is folded, presumably for shipping.The tubing was shipped in a plastic envelope and was folded twice leaving three creases. These creases are permanent and unsightly. It ruins an otherwise beautiful covering. I tried using the same methods of removing creases from neoprene—pouring boiling water over the creases and inside the tube. Even with boiling water inside the tube, I could comfortably hold the outside of the tube, verifying the insulation performance. While the boiling water relaxed some of the smaller creases, the deep creases stayed. Even after letting it sit for 24 hours, the creases remain.A note on installing. These tubes are bit snug to keep them in place. This tube's ID is 28mm. My tripod leg is 28.1mm. The tubing will stretch a little, maybe ±1mm. Carefully measure the round part where you plan to install this, preferably with calipers.To install them, DO NOT USE any sort of petroleum lubricant such as WD-40 or grease. The tubing will slip and not stay in place if you do. To help slide it onto whatever you're mounting this on, use 91% rubbing (isopropyl) alcohol. DO NOT USE ethyl alcohol. Clean the surface where it will go with the alcohol, then pour some inside the tube and swish it around. While it's still wet slip the tube onto the surface. The alcohol gives just enough lubrication to allow the tube to slip. If tube starts to stick, lift up an edge and pour a little bit more alcohol inside. The alcohol will eventually evaporate and the tubing will stick to the surface and stay in place.For the product, I give it 5-stars. For how they store and ship it, I give them 1-star, so overall, 3-stars.

Went on my wheelbarrow handle easy, just what it needed. Time will tell how it withstands use and the outdoors.

This material is very expensive but not suitable to protect 3/4" waterpipe. It must be cut lengthwise with a scissors. It is thin and very tight. It must doubled then secured with duct tape to properly cover a 3/4" waterpipe (1"o.d.). I'm not sure what this material could be properly used for, but IMHO it is certainly not adequate to protect a waterpipe from hard freezing weather. Don't waste your money.

Muy buen producto. Recomendado.

Nice quality material for 1” bars. I used isopropyl alcohol to slide on, and a hair dryer on low heat to evaporate the alcohol

The originals tore on my Elliptical, found them and they are a great replacement fit

I bought this to pad the neck holder of my guitar rack (Hercules Stands GS523B) ... fit snug (used some light oil to slide it on) and does the trick :)

I'm using this tube for lanyards which is soft on the back of the neck