CURT 19745 Universal Car RV Tow Bars for Flat or Dinghy Towing, 5,000 lbs, 2-Inch Coupler , Black

Works great! Towed my 2005 sebring convertible over a thousand miles to Georgia with out a hitch! (sorry the pun) This is everything they say and more.

Good quality, we had to wind up adding a little bit of a welded attachment for our 2010 Buick enclave but it worked out great! We just needed it to be a hair wider. But overall no issues towed from MT to FLA in snow rain and sun.

First of all, YES, the nuts are hard to turn. That way they don't fall off. This is part of the design. I am towing an old Land Rover with a big steel bumper. Easy to drill four holes and attach the brackets. I added extra washers, and wider washers as well. I really think the hardware should be grade 8 instead of grade 5. But it will probably be fine. I wish the brackets had enough room for the hitch to swing up so it could stay on the tow vehicle better. I can bungie cord it on though. Good value for the price. The unit is durable and sturdy. For off road towing, I would upgrade the hardware for peace of mind. But towing down the highway, this thing will be fine. An eyehook for safety chains would be a nice touch though. You have to supply your own chains or cables and find a place to connect them.

Well built. Being fully adjustable is great. The only thing it lacks are safety chains. I pulled a 2000 Silverado with it a couple times. Saved me a ton over calling a tow truck. Took about 20 mins to drill holes and install. Once attached, it was very sturdy and held up well in its use. After each use I checked all the fasteners and all had stayed at proper torque specs. I would recommend for light, occasional use. Don't know how it would do for long trips. Always a good idea to stop and look everything over if using on long trip anyway. Hope this helps.

Used this for the first time and put a total of 1,200 miles on it. Drove mostly interstate but a few short gravel roads on the trip. I checked the bolts at every stop and there was no signs of loosening or wear of any kind.The packaging was completely trashed when it arrived (assume that is why I got it cheaper from the specific retailer), but all items were included and it was unused in box.I bolted this directly to my TJ factory bumper which required drilling a couple extra holes. I also bought some larger diameter grade 5 washers and doubled them up with what was included in the box. No complaints and not afraid to tow this again and again. First trip I was a little nervous because I had never flat towed anything before. Worked flawlessly.

This hitch requires a flat surface for mounting. I had to remove the rubber bumpers but then could easily attach the hitch. I did temporarily remove the bumper using a 55 Torx socket. This hitch is built strong and I trust the brand.

Bought this product to tow a 6000lb chevy avalanche 600 miles from the top of Indiana to the bottom of Kentucky with our chevy sikverado. On the way back to Kentucky around 11pm we ran Into a sudden accident around a blind corner on the Interstate and had to slam on our brakes.. well, 11000 pounds of combined weight at 60mph doesnt stop easily. We locked the brakes and had to go into the grass median to avoid hitting the other cars stopped in the road. The tow bar held up with no problem! We stopped at the next gas station to inspect everything and it held up just fine along with our chains. I 100% reccomend this tow bar to anyone looking.

Make sure to tighten the bolts by the ball hitch! I had mine snug but it still moved around a little during my trip. I kept hearing funny sounds when I turned and it was because my nuts were two loose.I welded 4 peaces 3/8 plates with a 5/8 bolt for backup to my Tacoma frame. The ends of the tow bar were slightly smaller than the width of the frame and fit perfectly inside each set of plates. I couldn't use the brackets that came with it because I think they are for jeep bumpers or a solid metal bumper. I cut flaps in my Tacoma plastic bumper so when the tow bar isnt there the flaps cover the holes. The only hard part of my setup is I have to reach under my bumper to put the pins in.