EZDIY-FAB Vertical Graphics Card Holder Bracket Support with Multi-Angle,GPU Mount,Video Card VGA Support Kit with PCIE3.0 Riser Cable- White

Only gave 4 stars for easy install because the instructions are not clear at all. It took almost an hour just to put it together even though it has only 3 parts to screw together, the way it is designed makes it a bit confusing. Once together I noticed that the magnets are strong enough to hold it in place but you will want to make sure it's at the angle you want before putting in the case because trying to adjust in the case can cause issues. Other than those two things it looks awesome and as far as I can tell the riser cable is more than just average. I am very happy with it and would definitely recommend it.

I never leave reviews. But this product is such a waste of money that stressed me out by the install and even by negatively affecting my PC that I felt the need to warn other. The screw holes on the separate pieces of the mount don't align, no matter how much wiggling you do. The riser cable must also be faulty because hooking up my GPU with the cable caused my entire PC to lock up to the point that it needed to be power cycled. Disconnected riser cable and connected directly to PCIe slot and PC returned to normal functioning. Don't waste your money and risk wasting your time on installing a faulty product and damaging your PC (and your sanity). The only positive is that the magnets on the bottom are very strong and were able to securely prop up my hefty 4080.

Like others, the screw holes didn't want to align properly. This thing took me at least an hour to get aligned where the screw holes matched well and it came together, Always do your homework and read peoples reviews of pros and cons. this does not sit over the pre-existing slots on the pc case. you have to stick it to the power supply/ps shrowd and let the magnets do their job. I have a water cooled cpu, and at first having to back up the gpu inside the case, had to re-configure the radiator and fans to accomodate the extra inch of the card sitting a little further back. before temps on my 5700 xt were horrid at least 70 celsius. Tested with Ghost Recon Breakpoint for a solid hour and temp never passed 64 celsius. i have it standing on its side not leaning within the case. I'm sold on this device, I will most likely purchase 2 more, one for each of my son's pc's. I do recommend this if you take your time to do things right. otherwise you will get frustrated at mounting and installation.

Was doing a build in a Phantek Evo X. Kind of a Retro Build. Have been meaning to use this case for the last year and a half and finally getting around to it. Used a Distro plate that blocked the PCI-E slot for the GPU and planned on using a EKWB water-block. No sense in hiding 250.00 dollars worth the GPU'S LED'S. Would like to see it updated to PCI-E 4.0. I know there's not that much difference in timings, but still.Like the magnets on the bottom of the bracket. Makes it very easy to line up the HDMI or Display Port Cable coming out of the back. Have a Cable-Mod Vertical mount, but couldn't use it because of the Distro Plate.

-Pros-Makes your GPU look amazing in it's case!Decently sturdy.Magnetic feet.Easy to adjust.-Cons-Not Gen4 PCIe so if you run an RTX card you will need to swap the extender cable.Different cable may not align with mounting holes... mine didn't.(Thermaltake TT Premium PCI-E 4.0 High Speed Flexible Extender Riser Cable 300mm with 90 Degree Adapter AC-058-CO1OTN-C2)Because of this I had to use motherboard standoff screws to extendthe faceplate bracket to allow the PCIe slot to line up properly.Magnetic feet have a low quality felt-like material that gets easily marred and gummy if heated. Scrape this s#!t off and use something better or you'll be scraping it off the bottom of your case.-Overall Review-After some tweaking and adding a couple extended motherboard standoffs I was able to get my EVGA RTX 3080ti FTW3 Ultra to mount and tilt back enough to look amazing in the case with a proper PCIe GEN4 cable I had to replace the stock one with. The mounting holes for my replacement cable did not line up with the mounting bracket so unfortunately I had to mount the cable somewhat crooked, but not too bad. The magnetic feet are strong but the felt-like gunk they use to cover the magnets is garbage. Replace it with something better, or just remove it. Overall despite the amount of tweaks I had to do to get my GPU mounted sufficiently, placed properly in the case and looking good, I am happy with the results!

I bought this to mount an RTX 3080 in a custom-built 2020 aluminum extrusion "case". I did not use the swivel, because that is dumb. Once assembled, the GPU mount is VERY sturdy and offers no wobble. I am completely confident that my RTX 308o is safe and isn't going anywhere. The included PCI-E riser cable is nicely made. It is flexible enough and locks into place nicely.The only con I can think of is when you mount the GPU into the other end of the riser, it doesn't seat 100% but this does not affect the performance or stability of the card in any way.

The media could not be loaded.  I thought not, but it is compatible with the best graphics on the market, the 4090, this support to put your video card is perfect and does what it says, the only thing I had to do is put a graphics support on it because the design of my case is inclined, I recommend it 5 well-deserved stars!!!🙌

Installed this and the computer would not boot. Kept hanging on posting video. Removed it and Installed directly into the motherboard and computer booted right up. Also, unless your case has an opening for the monitor cable to go through than this is not an easy hookup. Is designed not to mount the card with the dvi, hdmi connections are not outside the case.

Llegó en tiempo y forma, material de buena calidad y facil instalación... De momento todo bien.

Riserkabel funktioniert prima! Montage ist kinderleicht und die Funktion die GPU leicht schräg zu positionieren ist für meinen Bedarf einfach genial gewesen! Preis Leistung Top! Andere riserkabel sind ohne Halterung schon teurer und die magnetlösung ist einfach toll!

組立が少し、簡単なのに若干面倒ですが後はライザー繋いでケースにマグネットで取付けるだけでOK。自分はAORUS2070superですが全然安定してます。特にぐらつく事も無くいい感じです。少し角度付ける感じで設置しました。耐久性はわからないのでとりあえず星4ですが、色々探しましたがこれで良いんじゃないかと(^ ^)

Nach 2 Jahren Benutzung im pc (worin der pc über 1 Jahr stand weil ich Vater geworden bin) hatte ich durchgehend Bluescreens aufgrund eines Hardware Fehlers. Die rtx3080 habe ich zeitgleich mit dem riserkabel gekauft und müsste eigentlich noch in Ordnung sein also ohne riserkabel verbaut und keine bluescreens mehr. Schrott

Paketleme çok kötü, ürünün sistemi ve yapısı güzel fakat üretim aşaması sıkıntılı. Çünkü ayak destek noktalarında bariz eğim hatası mevcut. Kullanılan beyaz boya çok kalitesizdi. Bir kaç temasta boyasını bırakıyor. Kasa içine yerleştirdikten sonra açı/eğim vermek çok zor. Nedeni ise dar alanda vidaları sıkmak mümkün değil. Vidaları kelebek vida ile yapılsa veya klips veya kelepçeli olsa daha ergonomik daha kullanışlı bir ürün olacaktı.