Lammcou Suction Cup Mount for GoPro, Action Camera with 360° Dual Head Ball, Car Suction Cup Holder for Insta360 X3 X2 Go3 Hero 13 12 11 10 Accessories

Grips extremely securely, is very easy to adjust and feels very well built, much more so than plastic ones.I mounted an Akaso action cam to it on the windscreen of a car and holds that weight very easily, would certainly hold much more.

Fine, does the job and feels robust, I trust it with my GoPro.

Mounting a camera on a surface gives you extra angles and magnetic mounts are great at this but not all useful surfaces are magnetic - some are very smooth and flat though and that is where this comes into its own. Instead of a magnetic field to hold the mount in place, there is air pressure.The suction cup on this is 92mm in diameter and the centre of the cup travels to around three times the original displacement when you set the lever so that gives a theoretical maximum of 45kg or 100lbs.However, add into that the fact that unless you are mounting it on glass, other surfaces will leak air into the suction cup. I tried this on the painted side of the filing cabinet with an action camera on it and it stayed there for around 15 hours before it fell off - I don't expect a test on glass to result in anything less than several months.So, with real world cameras weighing in at a fraction of its theoretical maximum load carrying capacity, there is ample suction there.The suction cup unit is made from plastic which is fine as the forces involved are not that great and it joins the rest of the unit via a plastic ball.At the other end of the magic arm you can have either: a standard 1/4" British Standard Whitworth threaded bolt so you can mount your camera or other equipment on that; or, an Action Camera mount - you can see both of these in the photographs.The arm is metal but the balls at either end are plastic so it all needs to be bigger than if would if the balls were metal.When using it, it does produce a nice, firm hold on which you can put your camera and you know that if you can trust the surface, it will hold, although like all things, a backup tether is probably a good idea if you are going to use it on the outside of a car door.Being able to fix you camera to glass and other flat surfaces is really useful and this lets you do that easily.

I ordered this to replace a smaller mount I already used within my car to Mounty Insta360 Go 3, whilst that was perfectly fine for it's intended purpose it just wasn't strong enough to support my Insta360 One R which would drop to the floor within seconds.I'm pleased to say this does the job I intended it for, whilst being much heavier than my old one as it is an all metal construction, this is compensated for by a much larger suction cup which has so far had no trouble clinging to the glass roof of my car.I have also mounted it to the bonnet, which is plastic, for point of view shots similar to what I achieve on my motorcycle and it has managed to stay fixed though I haven't gone above 30mph and don't intend to until I am much more confident in it's suction abilities.I did wonder if I could use it to attach an invisible selfie stick to get 360 overhead shots whilst driving but I don't feel that it would support this, the additional length seems to cause too much leverage so not recommended, a 3 cup device is the way to go if you wish to film that way.All in all I am very happy with the performance so far, I have a cupboard full of car mounts that have failed me in one way or another, looks like I have finally found one that works!

Acquired item to use with my action camera. It's well made, and the ball joints once tightened even with the camera attached stays in there locked position.The suction cup is secured by means of a lever. Worked great for me on my van. Plus easy to remove.Included with the mount, a gopro or 1/4 camera mount which is very easy to change as desired.This is a well made, sturdy mount, plus very competitively prices IMO. Very pleased.

This makes for some nice dash cam footage. Solid build and the suction cup is very strong.

This is much better than the usual cheap rubbish you get, the pivot balls are a good size and rubber coated so when you tighten up the screw, the balls stay put without you needing to put a lot of effort in. The GoPro mount can be easily fitted by loosening up the screw until you can open the arm enough to get the mount ball out.

£20 at time of reviewWorks pretty well, I did try it on my dashboard initially, and it worked, but as the dashboard itself has a slight raised texture I felt it would come loose after a while, so attached it to the windscreen instead and it felt rock solid. Comes with a ball to a action cam mount plus a standard 1/4 tripod thread, so you can swap them over, or even remove the whole arm from the suction mount and use the two ball mounts to connect to a camera cage etc, I’m unlikely to do that as I have magic arms for that, but in a pinch it could be useful, so quite a neat design.Hope my review was helpful

Wertigkeit Ausführung. Sauger hält auf Motorhaube auch Krefelder Kissen aus. Trotzdem empfehle ich Sicherung über reißfeste Schnur.(Taklinggarn!)

Cette ventouse est remarquable : très bon maintien sur la voiture ainsi que sur la moto ( sur le reservoir). Jusque 70 à 80 km/h je n'ai eu aucun souci. Le système de réglage a "boule" est très efficace. Il permet des réglages quasi 360 °. Je conseille de passer une microfibré à l'endroit où va être positionner la ventouse (pour enlever les éventuelles poussières). J'installe soit ma Gopro soit une Insta 360 x3. Le seul point que je ne peux évaluer c'est la tenue de la peinture. En effet je l'ai que depuis quelques semaines. Ce produit est, en conclusion, très efficace

Pratique et fait parfaitement le job

a bit bad suction pad. Could have used a "press" button for extra vacum like "gopro original".This one needs to be pressed firmly down the lever and cup to make good contact. Would not trust this on high speed vehicles with an expensive camera. But if used for other purposes it will do just fine.

Se trata de un soporte de tipo ventosa para nuestra cámara de acción.Lo que es el brazo del soporte es mediante dos bolas o rotulas que le da toda la movilidad posible y es muy fácil encontrar la posición correcta.La ventosa es grande y tiene una adherencia pero con el tiempo supongo que pasará como con todas las ventosas que van perdiendo la adherencia y se cae y hay que volver a colocarlas,pero en principio es un buen soporte.